Hardware. Firmware. Software. One engineering partner.Based in India · Working worldwide   Deutsch ↗
iTechGeeks engineering

PCB reverse engineering and schematic recovery services

PCB reverse engineering, schematic recovery and bill-of-materials documentation, informed by experience across more than 100 boards.

Recover the engineering behind your circuit board. We reconstruct circuit information from existing PCBs into schematics, component documentation and a record of what has been confirmed. The work can support maintenance, documentation recovery and assessment of a redesign.

When a PCB reverse engineering service is useful

An undocumented circuit board can hold up a repair, a supplier change or an assessment of whether a product can be supported for longer. Our electronics reverse engineering services help recover the information needed to make that decision. Start with the outcome you need: understanding a failed circuit, rebuilding missing documentation or defining requirements for a replacement.

A working sample and a failed sample answer different questions. The working unit can provide reference behaviour; the failed unit may reveal damage but cannot establish how the original circuit should perform. If only one sample exists, agree which inspection methods are acceptable before any component is removed.

Match the investigation to the decision

PCB recovery scope by business need
Starting problem Useful recovery scope Next decision
Missing design files Reconstruct agreed circuit blocks, identify components and document uncertain connections. Can the documentation support maintenance, or is further investigation needed?
Obsolete component Recover the surrounding circuit and its electrical/interface requirements. Can a substitute be validated, or does the circuit need redesign?
Unexplained board failure Document the affected circuit and compare available samples under agreed test conditions. Is the evidence sufficient to isolate a fault and plan a repair?
Replacement board needed Recover functional requirements and interfaces, then define a separate design and validation scope. What must the replacement demonstrate before it can be used?

What makes recovered information usable?

The important distinction is between observed information and engineering inference. A readable component marking, a measured connection and a proposed equivalent part should not appear as equally certain entries in a BOM. Ask for unresolved items to remain visible, with the checks needed to close them. This makes the handover useful to the next engineer and prevents an assumption from becoming an undocumented design requirement.

If the investigation leads to a replacement, our PCB design service can be scoped around the recovered requirements. Review our experience documenting more than 100 PCBs, then share the board condition and the decision you need the work to support.

From your board to a documented circuit

  1. Intake: review the board’s purpose, condition, available samples and any partial documents.
  2. Agree the scope: identify the circuit areas, outputs and validation checks required. Record limits on board access and examination methods.
  3. Identify components: record markings, packages and component references. Keep uncertain identifications visibly separate from confirmed ones.
  4. Reconstruct connectivity: trace and document connections for the agreed scope, with inaccessible or ambiguous details recorded for review.
  5. Review the reconstruction: check references, connections and documentation against the available evidence. Agree separately whether functional checks on powered hardware are included.
  6. Hand over: provide the agreed schematic, BOM and supporting notes, including unresolved questions and revision identifiers.

What belongs in the handover package?

Agree the deliverables before work begins
Deliverable Information to include
Schematic Circuit blocks, component references, connections and revision information for the agreed scope.
Bill of materials Identified parts, quantities, component references and a clear indication of unconfirmed items.
Review notes Inspection or measurement checks performed, conditions and unresolved details.
File-format agreement Agree the native design-tool version, editable files and review exports before quoting. The output should fit the tools your team will use.

A schematic and BOM describe an electronic assembly; they do not by themselves certify its safety or establish that a replacement board will perform identically. Functional validation and redesign are separate scope decisions.

What affects the quote?

Layer count, accessible interconnections, missing component markings, board condition and sample availability affect the investigation. So do the amount of circuitry covered, the required review depth and the requested documentation format. Photographs help scope the work, but access to a physical sample may still be needed.

Send a useful starting brief

  • Clear photographs of both sides and the board’s dimensions.
  • What the board does, known supply and interface details, and any fault history.
  • Existing schematics, part numbers or documents, even if incomplete.
  • The number and condition of samples available.
  • The desired output: documentation, repair support or assessment for a redesign.
  • Your preferred file formats, timeline and any restrictions on examining the sample.

Schematic recovery, firmware extraction and redesign are different jobs

Choose the scope that matches your objective
Scope What it addresses What it does not automatically include
Schematic recovery The components and electrical connections of the existing board. Firmware, manufacturing readiness or verified equivalence of a replacement.
Firmware extraction Whether software can be obtained from a particular programmable device. A guaranteed result or an editable source-code project. This needs a separate feasibility discussion.
Functional redesign A revised implementation against agreed requirements. Automatic preservation of the original behaviour without a defined validation programme.

Relevant PCB documentation experience

iTechGeeks has reverse engineered more than 100 PCBs for different companies, including schematic and bill-of-materials recovery. Our PCB documentation project summary describes this experience and the limits of what a board investigation can establish.

For a new board rather than recovery of an existing one, explore hardware and PCB design.

Discuss your board and deliverables ↗

Common questions

What clients ask before starting

What do you deliver when a board is reverse engineered?

A typical package is a readable schematic, a bill of materials with the components we were able to identify, notes on the board stack-up, connectors and test points, and an explicit list of anything that could not be confirmed. The exact deliverables are agreed with you before the work starts.

Can you work from a board with no documentation at all?

Yes. That is the usual starting point. We work from the physical board, the components on it and the behaviour of the circuit rather than from existing design files.

What happens when a component is unmarked or obsolete?

Where a part has been sanded, relabelled or discontinued, we identify it from its package, pinout and behaviour in the circuit where that is possible. If a part cannot be confirmed, it is recorded as unidentified rather than guessed, and we set out candidate replacements for you to evaluate.

Do you need the physical board?

Access to a physical sample gives the most reliable result, because layer-by-layer inspection and measurement are usually needed. High-resolution photographs and scans can support the work but rarely replace a sample.

What do you need from us before starting?

A description of what the board does or should do, any partial documentation you already hold, and confirmation that you have the right to have the board examined.